this thread is for post exam discussion for junior engineer exam 2013. so that candidates can have idea about the cut off marks and answer keys
this thread is for post exam discussion for junior engineer exam 2013. so that candidates can have idea about the cut off marks and answer keys
best of luck to everybody for tomorrow's exam. dont forget to share ur experience after exam
bhai log exam kaisa gaya.............aur isme kaisa selection hota hai................any idea plse share???????????????????????///
Is anyone has any idea about the no. of vacancies???
has anybody from mechanical done this question?
shear stress in a turbulent flow depends upon??
shear stress distribution in a turbulent flow is??
if yes plz answer...
has anybody from mechanical done this question??
a circular shaft can transmit a torque of 13 kNm. if the torque is reduced to 12 kNm then the maximum value of bending moment that can be applied to the shaft is
- 5 kNm
- 1 kNm
- 3 kNm
- 7 kNm
0 voters
has anybody from mechanical done this question??
a circular shaft can transmit a torque of 13 kNm. if the torque is reduced to 12 kNm then the maximum value of bending moment that can be applied to the shaft is
1) 1 kNm
2) 3 kNm
3) 5 kNm
4) 7 kNm Skip
—
ans is 5 use equivalent twisting moment eq here...though i did not attempted in paper
€‹
hello frndzz.. any update about ssc je exam???
when the key and result will come...any idea bhai log...
guys key released,,,am getting 80 OBC..any chances for next level
guys ans key released...share ur marks
guys few question of technical and reasoning question's answer in the key are wrong,what u said about that........
http://ssc.nic.in/whats%20new%20html/latest_news/MOR_2013.pdf
ques with wrong ans key(m.e)-
1. angle b/w d face and flank is lip angle(ans-c)
2.in thermit welding prop. of aluminium and iron is 1:3(ans-a)
3. if 2 liquids r mixed at different temp den d final temp can be found out by 2nd law of thermo as mixing is irrerversible(not sure about dis one)(ans-c)
4. power transmitted by a circular shaft 2*PI*N*T/60(ans-b)
5. a single slider crank chain has 1 sliding and 3 turning pair(ans-b)
aptitute ques r also wrong 2 figure type quest
bhai jo cand JE2012 mei v appear hue the please comment here...wanna discuss smthing
FEW MORE ANSWERS ARE WRONG:
1) In assesrtion and reasoning question in technical part answer given is that section modulus of I-section is low where as it has the highest section modulus.
2) In which milling operation , is the surface finish better ?
Both climb milling and down milling are correct because both mean same thing. hence this question has 2 answers.
3) ____ , PSV , EHK , TWZ , ILO
Both (A) and (D) are right answers.
Since no fax no. is given so those living in delhi should personally meet the deptt.
FUTURE IN STAKE.........................................................
REQUEST TO EVERYONE please inform all ur fnds also who appeared in exam and also include it in representation to SSC
last year SSC ne paper 2 ki cut off total 2000 cand ( who qualified in paper1) ke hisab se calculate ki thi...jabkiGEN ki cut off 1000 cand( jo UR standard par qualify hue ) unke hisab se honi chahiye thi...bcoz a cand who once qualifyat relaxed standard in pre stages ..can not compete for UR seats in later seats..its rule..par baad mei final result mai ssc ne final result mai correction ki..aur 100 UR seats khali reh gyi...isse GEN nd OBC dono ko nuksan hua